|
Drawworks |
One (1) OIME SL-5 drawworks 700 HP, Parmac 343 Hydromatic brake, drum grooved for 1 1/8” drilling line, Crown-o-matic |
|
|
|
|
Catworks |
One (1) OIME C-7, 400 HP, with torque tube with one each model 37AH make up cathead and one model 24AH break out cathead |
|
|
|
|
Mast |
One (1) Parco 550-K cantilever mast, 131’ tall mast with mast stand, Tong counter weights, Ladder, Derrick climber, Geronimo |
|
Static hook load with 10 lines – 550,000 lbs maximum wind 85 MPH, with 4 inch 5,000 psi standpipe & standpipe manifold |
|
|
|
|
Substructure |
One (1) substructure Parco split level, 550,000 lb hook load with maximum pipe setback capacity 400,000 (simultaneous) 18’ height above ground with 15’ clear height under the rotary table |
|
|
|
|
Rotary Table |
One (1) Pyramid-Hacker 27-1/2” rotary table rated at 275 tons, disk back brake system with split rotary table bushings |
|
|
|
|
Engines |
Three (3) Caterpillar 3408B engines 375 HP each with Allison CT6061 transmissions on compound |
|
|
|
|
Mud Pumps |
Two (2) 1000HP triplex mud pumps independently driven by Caterpillar D-399 engines |
|
|
|
|
Travelling Block |
One (1) Ideco model shorty, 260 ton traveling block, 5-36” sheaves and 1-1/8” line |
|
|
|
|
Hook |
One (1) ideco, model shorty, 260 ton |
|
|
|
|
Elevator Links |
One (1) set elevator links, 2-3/4” x 114” x 300 tons |
|
|
|
|
Swivel |
One (1) Ideco swivel, model TL-300, capacity 300 tons |
|
|
|
|
Drill Line |
One (1) 5000’ of 1-1/8” drilling line with |
|
|
|
|
Deadline Anchor |
One (1) National type D deadline anchor with Martin Decker type E-80 load cell |
|
|
|
|
Air Hoists |
Two (2) Ingersoll Rand K5UL air hoists with 5/8” wire line |
|
|
|
|
Crown Block Assembly |
One (1) OIME 5-36” sheaves and 1-52” fast line sheave grooved for 1 1/8” drilling line |
|
|
|
|
Toolpusher’s Trailer |
One (1) Rig Manager trailer with two each bedrooms, two bathrooms, kitchen, laundry room |
|
|
|
|
Mud Conditioning Equipment |
Mud pits – 720 total barrels
1-270 bbl suction pit with four compartments, three Brandt 10HP mud agitators, one mixing mud hopper and one 50 HP 5 x 6 Halco 2500 supreme centrifugal pump. |
|
1-200 bbl shale pit with four compartments, 1-Brandt 10HP mud agitator and 3 each per tank 3” mud guns with 1 ¼” nozzles |
|
1-250 bbl storage pit with two HP mud mixers powered by one 5 x 6 centrifugal pump |
|
One (1) Derrick mud cleaner FLC 3 panel with 20-4” desilter cones powered by 50HP MCM 5 x 6 Centrifugal pump |
|
One (1) Harrisburg desander with 1-12” desilter cone, powered by 50HP MCM 5 x 6 centrifugal pump |
|
Two (2) Derrick flow line cleaners |
|
One (1) mud bucket with 5 and 3-1/2” inserts, discharge hose to the flow line |
|
One (1) mud line, manifold: 4” 5000 psi mud line with 6-4” 5000 psi Demco gate valves and 3-4” 5M# vibrator hoses |
|
One (1) rotary hose, 3 ½” ID with 4” unions, 5000 PSI WP, length 60’ |
|
|
|
|
BOP Equipment |
One (1) Hydril annular BOP, 13 5/8” , 2000 psi stud top and 13 5/8” flanged bottom 3000 psi |
|
One (1) Washington rotating head series 1300, 13 5/8” bottom flange 3000-5000 psi, 150 psi WP |
|
One (1) Cameron double BOP, 13-5/8” 5000 psi, type U, flanged top and bottom with 4-3-1/16” 5000 psi outlets and standard 11” cylinders |
|
One (1) Cameron hydraulic actuated gate valve, operated, 4-1/16” 5000 psi |
|
One (1) Cameron gate valve, manually operated, 4-1/16” 5000 psi |
|
One (1) Cameron gate valve, manually operated, 2-1/16” 5000 psi |
|
One (1) choke line, armored fire resistant API flexible hose 3” 10,000 psi, 3” ID, API 4 1/16” flanged both ends, 44’ 8” long |
|
One (1) Kill line, steel flex hose, 5000 psi, 2” ID, API fig 1002 hammer unions |
|
One (1) choke manifold with 2 each 4 1/16” 5000 CIW Type FC manually operated gate valves, 5 each 3 1/16” 5000 psi CIW Type F manually operated gate valves, 1 each 5000 psi 4” Oteco manual operated valve 2 each 5000 psi 2 1/16” Cameron manually operated gate valve, 1-4 way tee block, 2 each 2 1/16” 5000 psi manual operated hydraulic choke, 8-5/8” OD header pipe, 2-3-1/8” 5000 psi flanges and 1-4-1/8” 5000 psi flange |
|
One (1) Air remote control unit mounted inside top dog house with access to control valves from the rig floor |
|
One (1) lot colflex BOP hoses, One (1) Degasser |
|
|
|
|
Air Compressors |
One (1) Quincy piston compressor, model 390LVD-A, with 20 HP electric motor and 300 gallon receiver tank |
|
Two (2) air dryer, Airtek desiccant type, model TW55 T( 4103-09K, (arctic class) |
|
|
|
|
Handling Equipment |
One (1) set Woolley type B tongs, with jaws for 3-1/2” to 10-3/4”, 11-3/4” and 13-3/8” |
|
|
One (1) Oil works Kelly spinner with RH & LH air drive motors, 6-5/8” regular Box & Pin |
|
|
|
|
Drill Collars |
TBD |
|
|
|
|
Drill Pipe |
TBD |
|
|
|
|
Miscellaneous Equipment |
One (1) 550 bbl water tanks, two (2) each 3 x 4 centrifugal pumps with 25HP AC electric motors |
|
One (1) 285 bbl fuel tank, 2 each 3.5HP 1 x 1 ½ centrifugal pump, 2 each Roper transfer pumps and Winslow duel sock fuel filter system |
|
One (1) utility house with accumulator unit, (1) each Koomey model 80, 5 station, 12-20 gallon bottle (10gallon useable fluid), powered by Koomey triplex pump powered by 10HP electric motor and two air driven pumps |
|
Two (2) Armstrong generators, each generator 300 KW, 480 volts, each powered by an Ideco engine, one AC transformer main rig power KVA 45, one AC Transformer KVA 45 on separate skid, both air cooled and diesel fuel day tank |
|
One (1) Westinghouse control panel, dual generator system with nine (9) breakers |
|
One (1) Quincy piston compressor, model QR390 with 20HP electric motor and 400 gallon receiver tank |
|
One (1) Totco drilling recorder to indicate drilling depth and record rate of penetration, weight of drilling assembly, pump pressure |
|
One (1) drillers instrumentation box with Martin Decker weight indicator, type clipper, Atlas pump pressure gauge, tong line pull gauge, rotary torque gauge |
|
One (1) drillers instrumentation console with control valves for M/B tongs, mud pumps, transmission shifters, rotary table and drawworks hoisting clutch |
|
One (1) lot utility suitcase, with Koomey lines, water lines, steam line, air line and electric cables inside |
|
One (1) Mathey wireline unit with 15,000’ of .092 wire line, 15HP electric motor |
|
Two (2) Flapper type float valves (6” & 8”) |
|
One (1) bottom change house with 19 each lockers, benches and insulated with one (2) electric heater and parts room (10’ x 40’) |
|
One (1) top dog house with drillers knowledge box, tool box, electrical outlets, satellite automatic driller type Apollo and 1 each electric heter (10’ x 30’) |
|
One (1) set rig mats, 8’ x 12’ x 6’ |
|
One (1) lot of rig lights and wiring |
|
One (1) each of drill collar clamp for 9-1/2” and 6-3/4” drill collars |
|
Four (4) pipe racks, 28’ length x 43” high |
|
|
|
